Ball Bearing

Butt Hinges

Residential Spring

5/8" x Square Corner

Commercial Butt

Commercial Spring

Security Hinges

Stainless Steel Hinges

Double Action

Concealed Door Hinges

Screen Door

Wholesale Door Hinges

Door Locks, Knobs, Levers, and Deadbolts

Heavy Duty

Adj. Gate Spring Hinges

Weld-On Gate Hinges

T Hinges

Strap Hinges

Commercial Spring Hinges

Double Action Spring Hinges

Heavy Duty Strap Hinges for Gates

Heavy Duty BadAss Weld-On and Bolt-On Hinges

Heavy Duty Locinox Gate Closers and Hardware

Gate Locks and Latches

Safety Gate Latches

Drop Bolts

Farm Gate Hinges

Bullet Hinges

Gate Locks

Coded Gate Locks

Overlay Cabinet Hinges

Self-Closing Cabinet Hinges

Blum Cabinet Hinges

Concealed Cabinet Hinges

Full Inset Cabinet Hinges

3/8" Offset Cabinet Hinges

Demountable Hinges

Butterfly Cabinet Hinges

Small Butt Hinges

Lid Support and Stays

Overlay Cabinet Hinges

Drawer Slides

Cabinet Catches

Knife Hinges

Cabinet Knobs

Cabinet Pulls

Heavy Duty Hinges

Commercial Ball Bearing

Commercial Spring Hinges

Weld On Hinges

Wide Throw Hinges

Swing Clear Hinges

Locinox Gate Closers

Strap Hinges

Pivot Hinges

Concealed Hinges

Piano Hinges

Heavy Duty BadAss Hinges

Door Closers

Wholesale Door Hinges

Electrified Hinges

Commercial Locks

Lid Support Hinges and Stays

Furniture Hinges Table and Mirror

Marine Hinges

Parliament Hinges

Wide Throw Hinges

Swing Clear Hinges

Shutter Hinges

Torque Hinges

Piano Hinges

Continuous Geared Hinges

Barn Door Hardware

Bifold Door Hardware

Pocket Door Hardware

Lift Off Hinges

Wood Hinge Screws

Machine Hinge Screws

Door Installation Hardware

Door Stoppers Chocks and Silencers

Toolbox Bundles

Hinge Pins

Ball Catches and Strike Plates

Cabinet Catches

Flush Bolts

Handrail Brackets

Hinge Jigs and Templates

Weatherstripping for Doors

Door Thresholds

Gate Stops

Stainless Steel Eye Bolts

How To Measure Cabinet Pulls: A Step-By-Step Guide

Whether you are looking to replace old pulls and knobs or starting from scratch, it is vital for you to buy the right size. Here is how to measure cabinet pulls to enable you to get the right fit. Continue reading our guide and start shopping for cabinet hinges and more from Hinge Outlet, Inc. for workmanship that you can trust.

Measuring Drawer Pulls

Measuring drawer pulls involves first figuring out the three measurements which include the center-to-center distance, length, and depth/projection of the pulls. With knobs, you should focus on the depth/projection measurements as most knobs tend to be really wide or tall.

Measuring Center-to-Center Distance

If you are looking to replace your cabinet hardware and you already have pre-drilled holes in your drawer or cabinet, always buy new pulls that have the same center-to-center distance as your old pulls. Make use of a screwdriver to first remove your existing pulls before taking a measuring tape or ruler to measure from the center of the one screw hole to another. If your new drawer pulls cannot fit into the old screw holes, you can always fill the old holes with putty or wood filler. After filling them up, sand them down before restaining or repainting. New holes can be drilled after these steps have been completed.

Tips: When measuring in millimeters, you need to convert the measurements into inches. Take the millimeter measurements and divide by 25.4. Some common center-to-center distances include 64mm, 76mm, 89mm, 102mm, 127mm, and 203mm.

Measuring Length

The length of the pull is important as it needs to be proportional to the size of your drawers or cabinet. It is recommended for you to get a pull that is no longer than one-third of the height of the cabinet door and no longer than one-half of the width of the drawer. If you intend to replace your cabinet hardware and want the same length as the previous hardware, measure from one end of the cabinet to the other to derive the length. It is also important to consider the type of pull that you are looking to get. Measurements can vary by the type of cabinet pull.

Measuring Projection

Projection is also known as depth which refers to the area between the pull and the cabinet. This typically refers to the space where you grab onto the cabinet pull or knob. A larger projection will provide more space in your hands so they can fit between the pull and cabinet comfortably. Consider the level of comfort that you are looking to achieve when using your cabinet pulls. For those with larger hands or arthritic hands, it is ideal to have a larger projection. To determine your cabinet pull projection, open up your cabinets and determine how close they get to each other as well as to other objects in the kitchen. If your cabinets swing too closely together or onto another object, you can choose a smaller cabinet pull to prevent any damage from the impact of the swinging action.

Buy Top-Quality Cabinet Pulls from Hinge Outlet, Inc. Today

Hinge Outlet, Inc. provides free shipping for any orders above $100 and provides product exchanges if customers ordered the wrong finish or size. We also offer refunds if you are not satisfied with the product quality.

If you have any questions about our cabinet pulls, feel free to contact us today.

Search