Ball Bearing

Butt Hinges

Residential Spring

5/8" x Square Corner

Commercial Butt

Commercial Spring

Security Hinges

Stainless Steel Hinges

Double Action

Concealed Door Hinges

Screen Door

Wholesale Door Hinges

Door Locks, Knobs, Levers, and Deadbolts

Heavy Duty

Adj. Gate Spring Hinges

Weld-On Gate Hinges

T Hinges

Strap Hinges

Commercial Spring Hinges

Double Action Spring Hinges

Heavy Duty Strap Hinges for Gates

Heavy Duty BadAss Weld-On and Bolt-On Hinges

Heavy Duty Locinox Gate Closers and Hardware

Gate Locks and Latches

Safety Gate Latches

Drop Bolts

Farm Gate Hinges

Bullet Hinges

Gate Locks

Coded Gate Locks

Overlay Cabinet Hinges

Self-Closing Cabinet Hinges

Blum Cabinet Hinges

Concealed Cabinet Hinges

Full Inset Cabinet Hinges

3/8" Offset Cabinet Hinges

Demountable Hinges

Butterfly Cabinet Hinges

Small Butt Hinges

Lid Support and Stays

Overlay Cabinet Hinges

Drawer Slides

Cabinet Catches

Knife Hinges

Cabinet Knobs

Cabinet Pulls

Heavy Duty Hinges

Commercial Ball Bearing

Commercial Spring Hinges

Weld On Hinges

Wide Throw Hinges

Swing Clear Hinges

Locinox Gate Closers

Strap Hinges

Pivot Hinges

Concealed Hinges

Piano Hinges

Heavy Duty BadAss Hinges

Door Closers

Wholesale Door Hinges

Electrified Hinges

Commercial Locks

Lid Support Hinges and Stays

Furniture Hinges Table and Mirror

Marine Hinges

Parliament Hinges

Wide Throw Hinges

Swing Clear Hinges

Shutter Hinges

Torque Hinges

Piano Hinges

Continuous Geared Hinges

Barn Door Hardware

Bifold Door Hardware

Pocket Door Hardware

Lift Off Hinges

Refrigerator Hinges

Trailer Hinges

Wood Hinge Screws

Machine Hinge Screws

Door Installation Hardware

Door Stoppers Chocks and Silencers

Toolbox Bundles

Hinge Pins

Ball Catches and Strike Plates

Cabinet Catches

Flush Bolts

Handrail Brackets

Hinge Jigs and Templates

Weatherstripping for Doors

Door Thresholds

Gate Stops

Stainless Steel Eye Bolts

Everything You Need to Know About How to Fix a Sagging Double Gate

Many homeowners choose to have gates around their homes for security, safety, and even aesthetics. Great for homes with kids and pets, gates come in a wide variety of forms including entry gates, courtyard gates, driveway gates, and more. Given that gates are outside and exposed to the elements, it only makes sense that they will start to show signs of wear and tear over time. It’s common for gates, especially double gates, to start to sag but it’s extremely important to fix sagging gates as soon as you notice it. Maintain the integrity of the gates for security, safety, and appearance purposes by learning how to fix a sagging double gate. 

Tools Required for Fixing Sagging Gates

The first thing you need to do to fix a sagging double gate is assemble the necessary tools. These include a lever, a tape measure, a pencil, a circular saw, two-by-four lumber, a power drill with a screw tip, and a set of three-inch deck screws. You should be able to find anything you don’t already own at a local hardware store. 

Identify the Gate Issue

Figuring out exactly what’s wrong with your gate will determine how you proceed with fixing it. TO determine the root cause of the sagging double gate, check the gate post of each side of the double gate and inspect the plumb of each gate. Check for signs of damage on the post. If it is solid and plumb, the issue will probably be on one or both of these gates.

Raise the Gate to Fix the Sagging

Now is when you can really start to fix the sagging gate. Close both sides of the gate before sliding a two-by-four lumber under the outer edge of the gates to use as a lever. Lift it up, using it as a lever to raise the end of the gate. Place the lever on top of the cross-member of the gate and raise it until its level. Raise the lever even further until it is about one inch above the level point. Then slide a solid object below the raised section of the lever to secure it in place. Do the same for the other side of the double gate.

Attach the Brace to Cross Members

Using the circular saw, cut the corners off the board before positioning the brace over the cross-members. Attach the brace to the cross-members with the power drill and a pair of screws, securing the brace with the top, bottom, and middle cross-members. Repeat this for the second gate.


Remove the levers from beneath the gates and open and close both sides of the double gates to check the positioning of the gate.

Find Gate Hinges atHinge Outlet, Inc.

If you are looking forhinges for your double gates, look no further than Hinge Outlet, Inc.! Established in 2005, Hinge Outlet, Inc. is a reputable and reliable distributor ofhigh quality hinges sold at the best prices on the market. As the premier retailer for quality residential and commercial hinges, we here atHinge Outlet, Inc.  are proud to boast an extensive selection of different hinges to fit any of your needs.Contact us to find out how we can help you now!